software:pfsense
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
software:pfsense [2016/01/24 22:34] – [Squid Configuration] superwizard | software:pfsense [2018/01/02 20:44] – [pfsense ipv6 with comcast] superwizard | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Firewall Rule Basics ====== | ||
+ | |||
+ | From: https:// | ||
+ | |||
+ | < | ||
+ | any - 0.0.0.0 to 255.255.255.255, | ||
+ | |||
+ | Single host or alias - Select this and enter one IP address (1.2.3.4, aa: | ||
+ | |||
+ | Network - Select this and enter a network and mask (10.99.0.0/ | ||
+ | |||
+ | LAN net - The subnet configured on the LAN interface under Interfaces > LAN. On pfSense 2.2+, this also includes IP alias networks on that interface. | ||
+ | |||
+ | LAN address - The IP address configured on the LAN interface under Interfaces > LAN | ||
+ | |||
+ | zzz Net / zzz address - Works the same as LAN above but for other interfaces (WAN, OPT1, OPT2, etc.) | ||
+ | |||
+ | PPTP clients - Automatically locate and use the addresses of PPTP clients | ||
+ | |||
+ | L2TP clients - Automatically locate and use the addresses of L2TP clients | ||
+ | |||
+ | This Firewall (self) - Any IP address assigned to any interface on this firewall (pfSense 2.2+) | ||
+ | </ | ||
+ | |||
====== Installing the Ubiquiti UniFi Controller Software on pfSense 2.2 ====== | ====== Installing the Ubiquiti UniFi Controller Software on pfSense 2.2 ====== | ||
Line 86: | Line 110: | ||
====== pfsense ipv6 with comcast ====== | ====== pfsense ipv6 with comcast ====== | ||
+ | |||
+ | From: http:// | ||
From: https:// | From: https:// | ||
Line 100: | Line 126: | ||
</ | </ | ||
+ | From: https:// | ||
+ | |||
+ | |||
+ | < | ||
+ | Comcast will let you request no more than a /60. 16 /64 subnets on a personal network should be | ||
+ | more than enough for most people. | ||
+ | |||
+ | Business class service may be able to request larger allocations, | ||
+ | anything from /64 to /60 only, depending on how many subnets you need (1 to 16, based on number of bits). | ||
+ | |||
+ | Because of pfSense' | ||
+ | IPv6 address for your router on your LAN. You set up "Track Interface", | ||
+ | you want to use (which will only be 0 if you request a /64, could be 0-F if you request a /60). The LAN | ||
+ | interface gets a SLAAC address based on the interface' | ||
+ | </ | ||
+ | |||
+ | {{ : | ||
+ | |||
+ | |||
+ | {{ : | ||
+ | |||
+ | {{ : | ||
+ | |||
+ | {{ : | ||
+ | {{ : | ||
====== CONFIGURING DHCP SERVER AND DYNAMIC DNS SERVICES ====== | ====== CONFIGURING DHCP SERVER AND DYNAMIC DNS SERVICES ====== | ||
software/pfsense.txt · Last modified: 2018/01/06 04:12 by superwizard