Differences

This shows you the differences between two versions of the page.

--- software:unigraphics [2015/04/06 02:48] – [Plotter setup in UGNX 6 x32 on W7 x64] superwizard
+++ software:unigraphics [2015/04/27 03:49] (current) – superwizard
@@ Line 21: / Line 21: @@
 set UGII_SDI_BPS_JOBS_DIR=c:\temp
 set UGII_SDI_OVERRIDE_HOME=c:\temp
 %UGII_ROOT_DIR%\ugraf.exe
 </code>
 NXSA7-Riches-BeginningAndIntermediatePlotting.pdf: http://www-cad.fnal.gov/PLM_World/2006/academic_programs/NX/NXSA7-Riches-BeginningAndIntermediatePlotting.pdf
+<code>
+To plot in NX, you first define printer in printer group usint **File>Utilities>Printer Administration**.
+After defining the printer group and taking steps to tell NX ou your printer group, you can direct plots
+to a particulay printer by selecting the group and the printer via **File>Plot**.
+</code>
+<code>
+Reference: Environment Variables: C:\Program Files (x86)\UGS\NX 6.0\UGII\ugii_env.dat
+############################################################################
+#
+#  PLOTTER AND PRINTER ENVIRONMENT VARIABLES:
+#
+#  Variables in this section configure SDI plotting software used by NX.
+#
+#  By default, only variable UGII_SDI_BASE is set and other plotting
+#  variables are unset (commented out). NX uses variable UGII_SDI_BASE
+#  to initialize unset variables as shown below.
+#
+#  The base directory where the plot kit can be found.  All variables default
+#  to values based off of this variable.
+#
+UGII_SDI_BASE=${UGII_BASE_DIR}\nxplot
+#
+#  When plotting, NX will automatically append the sheet name to the jobname
+#  so that the files generated for different sheets can be distinguished.  If
+#  the sheet name is not wanted, then set the following variable to disable
+#  this functionality.  Turning this off will generate the same CGM jobname
+#  for multiple sheets, so it should be used with caution.
+#
+#UGII_PLOT_DONT_APPEND_SHEET_NAME=1
+#
+#  The location of the cgm to pdf conversion utility
+#
+UGII_CGM2PDF=${UGII_SDI_BASE}\bin\pdf
+#
+#  When you use cgm2pdf as an image for a plotter queue, the SDI
+#  software will call it with one parameter, the CGM file to be
+#  created.  In this case UGII_PDF_OUTPUT_DIR tells the cgm2pdf
+#  image where the output PDF file is to be created.
+#
+#UGII_PDF_OUTPUT_DIR=
+#
+#  When you use cgm2pdf as an image for a plotter queue, you may
+#  want to append the plotter output into one output PDF file.
+#  Use UGII_PDF_APPEND for this.  If it is set, then append will
+#  be done.  If it does not exist, then appending will not be done.
+#UGII_PDF_APPEND=1
+#
+#  This variable specifies a single printer group directory that is
+#  shared by all users. If you prefer to use multiple printer group
+#  directories, then specify the directories in a printer group list
+#  file instead. Before setting this variable, review printer group
+#  concepts presented in NX Help documentation.
+#
+#UGII_SDI_SERVER_CFG_DIR=${UGII_SDI_BASE}\config\pm_server
+#
+#  The directory that SDI software will use as default for input.  This
+#  will effect the directory that the user sees when they press "browse"
+#  in the NX Plot Print screen.
+#
+#UGII_SDI_IP_DIR=${UGII_TMP_DIR}
+#
+#  The directory that SDI software will use as the default for output.  This
+#  will effect the default directory when a user plots to a file.
+#
+#UGII_SDI_OP_DIR=${UGII_TMP_DIR}
+#
+#  SDI software will normally add a PS command to HPGL and HPGL/2 output.  You
+#  can turn off this behavior by setting the following variable to 1.
+#
+#UGII_SDI_CGM_HPGL_NO_PS=1
+#
+# The following variable is used to control the resolution used to convert
+# a CGM to an EMF file when printing a wireframe display.  The default
+# resolution is 600 DPI, the variable can be set from 200 to 9600.
+#UGII_SDI_CGM2EXP_RESOLUTION=600
+#
+#  Set the following variable to cause the SDI printing software to suppress
+#  the generation of registration marks at the corner of HPGL output.  Note
+#  This variable should be used instead of UGII_IGNORE_OFFSET which it
+#  replaces.
+# UGII_SDI_IGNORE_HPGL_OFFSET=1
+#
+#  Set the following variable to cause the SDI printing software to suppress
+#  the generation of registration marks at the corner of HPGL-2 output.
+# UGII_SDI_IGNORE_HPGL2_OFFSET=1
+#
+#  Set the following variable to cause the SDI printing software to suppress the
+#  message box that the Image exceeds the printable page size.
+# UGII_SDI_IGNORE_SIZE_WARNING=1
+#
+#  Set the following variable to specify the location for the output of the
+#  Gerber format executable
+#
+UGII_SDI_OUTPUT_DIR=${UGII_TMP_DIR}
+#
+#  This is the directory the SDI software uses to look for executables.
+#
+#UGII_SDI_BIN=${UGII_SDI_BASE}\bin
+#
+#  This is the location of the various fonts that are required when
+#  rendering PostScript fonts.
+#
+#UGII_SDI_ADOBE_PATH=${UGII_SDI_BASE}\fonts
+#
+# This is the top level directory where the language files are found for
+# displaying the SDI user interface.
+#
+#UGII_SDI_LANGUAGES=${UGII_SDI_BASE}\languages
+#
+# This directory is the directory where the actual language files are found.
+#
+#UGII_SDI_PM_LANGUAGES=${UGII_SDI_BASE}\languages\pm
+#
+# This points to the file used to display the SDI help.
+#
+#UGII_SDI_HELP_UGS=${UGII_SDI_BASE}\help\pm\default.htm
+#
+# This variable can be set to BPS or WORKGROUP. BPS is the setting for
+# SDI Basic Print Solution software provided with NX. WORKGROUP is the
+# setting for optional SDI Print Master Server software.
+#
+#UGII_SDI_SERVER_TYPE=BPS
+#
+# This is the directory where temporary jobs are created for the user when
+# plotting is done.
+#
+#UGII_SDI_BPS_JOBS_DIR=${UGII_TMP_DIR}\bps
+#
+# This is the executable used to implement the Basic Print Solution.
+#
+#UGII_SDI_SERVER_PLOT=bpsplot_sdrc.exe
+#
+# This variable determines the logo displayed by the SDI user interface.
+#
+#UGII_SDI_LOGO_NAME=NX
+</code>
 ====== Commandline Start and Stop ======